How to install the ezCAN for BMW F800
This is a step by step guide to installing the HEX ezCAN (Generation 1 and 2) on BMW F800 series bikes.
- F800GS Adventure – K75
- F800GT – K71
- F800S – K71
- F800ST – K71
- F800GS – K72
- F800R – K73
- F700GS – K70
- F650 (2008+ 2 cylinder) – K72
- K1200GT – K44
- K1300S – K40
- 1 x ezCAN Device
- 1 x Micro USB Cable
- 2 x Velcro Strips
- 4 x Cable Ties
- 8 x Stub Connectors
- 2 x Blanking Plugs
- 1 x Green Horn Input Connector
DOWNLOAD, INSTALL & CONFIGURE THE SOFTWARE
Watch a complete installation video here, or follow the step-by-step guide below.
LOCATE YOUR BIKE'S BATTERY, DWA AND HORN CONNECTOR
The F800S DWA connector is easy to find under the seat.
The horn is accessible if you reach down the left side of the fork.
Access the battery by removing the top body panel.
The DWA is located on the side of the fuel cap.
A close-up of the DWA connector with the diagnostic port in the background.
Remove this plug to install the ezCAN horn extension wire.
Here we see the ezCAN configured with the horn.
Finally, connect the horn extension wire to the matching wire on the ezCAN.
INSTALL THE ezCAN
UNDER THE SEAT
You can secure the ezCAN with the velcro strips provided after the accessories have been plugged in.
Important notice: If you can’t find the seat- you’re in trouble!
ROUTE AND CONNECT THE BATTERY WIRES
The battery is located under the centre trim panel. Remove the seat and the centre trim panel by removing the six or eight screws. Route both the ezCAN power supply and ground cables along the motorcycle’s rear sub-frame and over the rear side of the engine airbox, to the battery. Disconnect the battery wiring harness terminals from the battery and connect the ezCAN wires to the battery before re-connecting the factory wires.
IMPORTANT NOTE: First, unplug the battery negative wire and only attach it at the end again. This is good practice whenever you work on your bike’s electronics.
PLUG THE ezCAN
INTO THE CAN-BUS
- If your bike has a DWA, that is, ‘anti-theft alarm system’, you will see the DWA module in the small compartment under the rear half of the seat, in front of the taillight. Note the wiring harness plug connected to the module.
- Start by unplugging the CAN-Bus connector from the DWA control unit.
- The HEX ezCAN has two CAN-Bus connectors. Plug the male HEX ezCAN terminal into the CAN-Bus wiring harness and plug the female HEX ezCAN terminal into the DWA Control unit.
If your F800 does not have a DWA system, the end of the wiring harness plug will be covered by a plastic blanking plug containing an alarm-terminating resistor.
- Start by unplugging the cap from the DWA connector plug.
- Plug the male HEX ezCAN terminal into the CAN-Bus connector.
- Replace the cap on the female HEX ezCAN terminal.
That’s how easy it is!
IMPORTANT NOTE: Both the male and female ezCAN CAN-Bus terminals must be connected correctly. Do not connect to any other component or to any other part of the motorcycle’s wiring harness. If you do, the ezCAN will not function.
STEP 6: CONNECT THE GREEN HORN INPUT CONNECTOR (HORN TRIGGER WIRE)
Note: If you do not install the green horn input wire your high power accessory horn and Front auxiliary lights – strobe when horn active function will not work.
If you are going to install an accessory horn, connect the accessory horn to the chosen high-power output stub connector on the ezCAN. In order for the horn to work also connect the green horn trigger wire. The HEX ezCAN kit contains a green wiring harness with one terminal pin, branching out to two sets of two terminal pins.
Find the standard BMW horn on your F-series motorcycle. Disconnect the motorcycle’s horn connection from the standard horn. Connect the male two-pin plug of the green wire to the horn connection on the BMW wiring harness.
Connect the female two-pin plug of the green wire to the standard BMW horn.
CONNECT THE ACCESSORIES
The HEX ezCAN kit includes eight stub connectors with male connection terminals. The eight stub connectors are made up of the following types:
– 4 x three wire stub connectors
– 4 x two wire stub connectors
If your auxiliary lights have three wires use the three wire stub connectors. If not, the two-wire stub connectors must be used for accessories that have power and ground wires only.
If you are not going to use one or more of the circuit functions, it is recommended that you install a blanking plug over the unused output. The HEX ezCAN product contains two blanking plugs.
The colour-coding on the output wires must match the colours in the output configuration you select from the HEX ezCAN circuit function software. Red to red, yellow to yellow, etc. (Black wire is Battery Negative and the Red, Blue, Yellow and White are the Positive Supply.)
Take note that certain F800 models were released without an Info button / trip computer. Brightness adjustment while on the move for these bikes will not be possible.
Connect the terminals of the high-power stub connectors to the correct female terminals on the ezCAN.
Connect the spotlight’s ground wire to the ground wire of the stub connector.
If you are installing spotlights equipped with a third wire for light-intensity control, connect the spotlight control wire to the control wire of the stub connector. If the spotlight only has two wires, use the two wire stub connectors.
MAKING THE INSTALLATION EASIER WITH THE ezCAN EXTENSION KIT
Introducing the HEX ezCAN Extension Kit for ezCAN for Harley Davidson and ezCAN Gen II for BMW. This wiring kit provides an ezCAN user with everything that you would need to connect up your front auxiliary lights, brake lights and horn to the ezCAN, with additional connectors to facilitate other accessories. In addition, the kit also provides:
- A maximum length cable that can be trimmed to the correct length
- Female connectors (as per ezCAN connectors) with terminals and seals are provided so that they can be used when cable is trimmed to length
- Heat-shrink to finish off sheath when cable is trimmed
- Male connectors to be used on your auxiliary lights and accessories wires
- Sheathing for finishing of wiring on the light side
- You can also use the output stubs connected to the extension cable to wire up your lights.
STEP 8: TEST THE INSTALLATION
Most newly installed accessories can be tested simply with the ignition “ON”, but some brake functions will require the bike to be in motion and traveling above a certain speed. For example, emergency braking requires deceleration of more than 21km/h/s (kilometres per hour per second).
SAFETY NOTICE: Test and check your installations and accessories in a safe, controlled environment. Caution is advised at all times. Extra vigilance is required when testing new features or accessories. You do so at your own risk.
DISCLAIMER: HEX ezCAN is not liable for any injury or damage howsoever caused and all products and services are used at your own risk.